МК "МВС" buys and sells scrap and waste of aluminum, according to the classification:
Grade |
Title |
Mass fraction of chemical elements, % not more than |
Characteristics (description) |
Requirements |
Clog % |
А 1/1 |
Aluminum, not alloyed Electrical products |
0,25- silicon max 0,05- copper max 0,05- manganese max 0,05- magnesium max 0,4- ferrum max 0,07-zinc max |
Wire, bare wires cables and cords. |
In bundles, coils, stacks, bags |
0,5 |
Without varnish and paint |
|||||
Without the presence of a thin wire, wire grids, iron and other insulating materials. |
|||||
Dry and clean the scrap, not oxidized |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
Scrap cable products |
0,25- silicon max 0,05- copper max 0,05- manganese max 0,05- magnesium max 0,4- ferrum max 0,07- zinc max |
Wire, conductor of cables and cords insulated |
In bundles, coils, stacks, bags |
in fact, selective cutting from the consignment |
|
Without the presence of a thin wire, wire grids, iron and other insulating materials. |
|||||
Dry and clean the scrap |
|||||
А 1/2 |
Aluminum, not alloyed Electrical products |
0,25- silicon max 0,05- copper max 0,05- manganese max 0,05- magnesium max 0,4- ferrum max 0,07- zinc max |
Cable sheath |
In bundles, coils, stacks, bags |
1 |
Dry and clean the scrap, not oxidized |
|||||
Освобожденный от изоляции |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 1/3 |
Aluminum, not alloyed Food aluminum |
0,25- silicon max 0,05- copper max 0,05- manganese max 0,05- magnesium max 0,4- ferrum max 0,07- zinc max |
Scrap and lump waste, cans, flasks. Sheet waste with thickness not less than 1 mm and the connecting line switchgear, transformers, rectifiers |
In bundles, coils, stacks, bags |
0,5 |
Contains no iron, paper, plastic, ink, oil, grease, paint, synthetic materials |
|||||
Not clogged other metals and alloys |
|||||
Dry and clean the scrap, not oxidized, no soot |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 1/4 |
Aluminum, not alloyed |
0,25- silicon max 0,05- copper max 0,05- manganese max 0,05- magnesium max 0,4- ferrum max 0,7- zinc max |
Heat exchangers |
In bundles, stacks, bags, loose |
1 |
Dry and clean the scrap, not oxidized |
|||||
Split |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 2 |
Aluminum, not alloyed |
0,7- silicon max 0,5- copper max 1,0- manganese max 0,9- magnesium max 0,7- ferrum max 0,3- zinc max |
Scrap and waste, foil |
In bags, loose, rolls |
0,5 |
Dry and clean the scrap, not oxidized |
|||||
Not clogged other metals and alloys |
|||||
Without varnish, paint, paper and other materials |
|||||
Thickness up to 1mm |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact the balance melt |
||||
А 2/1 |
The deformed aluminum alloys with low magnesium content |
0,7- silicon max 0,5- copper max 1,0- manganese max 0,9- magnesium max 0,7- ferrum max 0,3- zinc max |
Beer cans |
In bags, loose |
0,5 |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys, materials |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions. |
|||||
А 3/1 |
The deformed aluminum alloys with high magnesium content |
1,0- silicon max 4,9- copper max 0,5- manganese max 1,8- magnesium max 0,9- ferrum max 0,9- zinc max |
Scrap and sheet waste with thickness not less than 1 mm
packaged |
In bags |
0,5 (2% in the winter season) in accordance with selective cutting of the consignment |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Allowed in bags presence of other groups of aluminum scrap (A2, A6, A3/3, etc.) of up to 3% |
|||||
Not allowed the presence of groups Б and Г |
|||||
Failure to comply with these requirements receives an additional clog in fact of cutting three bags |
in fact, selective cutting from the consignment |
||||
А 3/2 (А3/9 under the current) |
The deformed aluminum alloys with high magnesium content |
1,0- silicon max 4,9- copper max 0,5- manganese max 1,8- magnesium max 0,9- ferrum max 0,9- zinc max |
Small scrap and lump wastes with A3/1, sheet waste with thickness not less than 1 mm, boat |
Loose |
0,5 |
Dry and clean the scrap, not oxidized, no soot |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 3/3 |
The deformed aluminum alloys with high magnesium content |
1,0- silicon max 4,9- copper max 0,5- manganese max 1,8- magnesium max 0,9- ferrum max 0,9- zinc max |
Radiators |
In bundles, stacks, bags, loose |
12 |
Dry and clean the scrap, not oxidized, no soot |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 3/4 |
The deformed aluminum alloys with low copper content |
0,5- silicon max 0,05- copper max 0,05- manganese max 0,05- magnesium max 0,5- ferrum max 0,1- zinc max |
Metal profile |
In bags, loose |
Without varnish and paint 0,5% With varnish and paint 1% |
Dry and clean the scrap, not oxidized, no soot |
|||||
Not clogged by other metals, alloys |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting |
||||
А 3/5 |
The deformed aluminum alloys with high copper content |
0,3- silicon max 4,5- copper max 0,8- manganese max 1,8- magnesium max 0,3- ferrum max 0,3- zinc max |
Д16 Scrap and lump waste, sheet waste with thickness not less than 1 mm |
In bales, stacks, loose |
0,5 |
Dry and clean the scrap, not oxidized, no soot |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 3/6 |
The deformed aluminum alloys with high magnesium content |
1,0- silicon max 30- copper min 0,5- manganese max 1,8- magnesium max 0,9- ferrum max 0,9- zinc max |
Radiators containing copper |
In bundles, stacks, bags, loose |
7 |
Dry and clean the scrap, not oxidized, no soot |
|||||
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 5 |
Aluminum alloys of the system aluminum-silicon-magnesium |
13,0- silicon max 1,5- copper max 0,5- manganese max 0,6- magnesium max 1,0- ferrum max 0,5- zinc max |
Cylinder blocks and V-engines, Engine cylinder heads |
Dry and clean the scrap, not oxidized, no soot |
0,5 |
No varnish, paint, paper, earth, sand, dirt, oil film, and other nonmetallic inclusions |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact |
|||||
Failure to comply with these requirements receives an additional clog in fact of selective cutting from the consignment and sort |
0,5 |
||||
А 6/1 |
Aluminum alloys of the system aluminum-silicon-copper |
13,0- silicon max 8,0- copper max 0,5- manganese max 1,4- magnesium max 1,0- ferrum max 1,0- zinc max |
Factory defect, ingots |
In loose, stacks, bags |
0 |
Dry and clean the scrap, not oxidized, no soot |
|||||
Not clogged by other metals, alloys |
|||||
In default of these requirements applies to the A6/2 |
|||||
А 6/2 |
Aluminum alloys of the system aluminum-silicon-copper |
13,0- silicon max 8,0- copper max 0,5- manganese max 1,4- magnesium max 1,0- ferrum max 1,0- zinc max |
Motor scrap iron content and the total clogging of less than 5.5% |
Loose |
0,5 |
Dry and clean the scrap, not oxidized, no soot |
|||||
Clogged other metals (iron additions). Split partially (with cut studs, without cast-iron liners, etc.) |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 6/3 |
Aluminum alloys of the system aluminum-silicon-copper |
13,0- silicon max 8,0- copper max 0,5- manganese max 1,4- magnesium max 1,0- ferrum max 1,0- zinc max |
Motor scrap with high iron content and total clogging up to 30% |
Loose |
30 |
Dry and clean the scrap, not oxidized |
|||||
Clogged other metals (iron additions) |
|||||
Failure to comply with these requirements receives an additional clog in fact of selective cutting from the consignment |
in fact, selective cutting from the consignment |
||||
А 6/4 |
Aluminum alloys of the system aluminum-silicon-copper |
13,0- silicon max 8,0- copper max 0,5- manganese max 1,4- magnesium max 1,0- ferrum max 1,0- zinc max |
Alloy wheels |
Loose |
0,5 |
Dry and clean the scrap, not oxidized |
|||||
Not clogged with other metals (iron additions, lead) |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 7 |
Alloys of aluminum doped with nickel |
13,0- silicon max 3,0- copper max 0,5- magnesium max 0,5- nickel max 1,0- ferrum max 1,0- zinc max |
Piston |
Loose |
0,5 |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys, without Piston rings and piston pins |
|||||
Failure to comply with these requirements receives an additional clog in fact |
in fact, selective cutting from the consignment |
||||
А 8/1 |
Scrap aircraft split |
0,8- silicon max 0,1- copper max 1- magnesium max 0,5- ferrum max 0,2- zinc max |
Scrap aircraft Helicopters Transport aircraft Mikoyan aircraft |
In bales, stacks, loose |
9 |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Chopped, cut into pieces no larger than 500х1000х1000 mm |
in fact, selective cutting from the consignment |
||||
Failure to comply with these requirements receives an additional clog in fact |
|||||
А 8/2 |
The deformed aluminum alloys with high magnesium content |
0,8- silicon max 0,1- copper max 13,0- magnesium max 0,5- ferrum max 0,2- zinc max |
Scrap and lump waste, sheet waste with thickness not less than 1 mm, АМГ, axle-box. |
In bales, stacks, loose |
0,5(Mg%=2 %) |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Chopped, cut into pieces no larger than 500х1000х1000 mm |
|||||
Failure to comply with these requirements receives an additional clog in fact When the content of Mg%>2 %, the calculation of clog to do according to the formula Mg(fact)- Mg(2%)=% additional clog Example: 6.8% - 2%=4,8% additional clog |
in fact, selective cutting from the consignment or cutting of large scrap and chemical composition |
||||
А 10 (packaged) |
The deformed aluminum alloys with high zinc content |
0,7- silicon max 2,6- copper max 0,5- manganese max 3,0- magnesium max 0,7- ferrum max 9,0- zinc max |
Scrap and lump waste, sheet waste with thickness not less than 1 mm, В95, АЦМ, Military scrap with high zinc content. |
Packaged |
0,5(Zn%=1%) |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact of selective cutting from the consignment and sort When the content of Mg%>2 %, the calculation of clog to do according to the formula Mg(fact)- Mg(2%)=% additional clog Example: 6.8% - 2%=4,8% additional clog When the content of Zn%>1 %, calculation of clog to do according to the formula Zn (fact)- Zn (1%)=% additional clog Example: 7% - 1%=6% additional clog |
|||||
А 10/1 |
The deformed aluminum alloys with high zinc content |
0,7- silicon max 2,6- copper max 0,5- manganese max 3,0- magnesium max 0,7- ferrum max 9,0- zinc max |
Scrap and lump waste, sheet waste with thickness not less than 1 mm, В95, АЦМ, Military scrap with high zinc content. |
Loose |
0,5(Zn%=2%) |
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact of selective cutting from the consignment and sort When the content of Mg%>2 %, the calculation of clog to do according to the formula Mg(fact)- Mg(2%)=% additional clog Example: 6.8% - 2%=4,8% additional clog When the content of Zn%>2 %, calculation of clog to do according to the formula Zn (fact)- Zn (2%)=% additional clog Example: 7% - 2%=5% additional clog |
in fact, selective cutting from the consignment |
||||
А 10/2 |
The deformed aluminum alloys with high zinc content |
13,0- silicon max 2,6- copper max 0,5- manganese max 3,0- magnesium max 1- ferrum max 9,0- zinc max |
Small scrap of aluminum with А3/2, А6/2,А6/3 |
Loose, small things |
0,5 |
Dry and clean the scrap, not oxidized |
|||||
Clogged other metals, including those which are not determined by the visual method |
|||||
Failure to comply with these requirements receives an additional clog in fact When the content of Zn%>2 %, calculation of clog to do according to the formula Zn (fact)- Zn (2%)=% additional clog Example: 7% - 2%=5% additional clog |
in fact, selective cutting from the consignment |
||||
Б 3/3 (Shavings of aluminum) |
Shavings of aluminum alloys with high magnesium content |
1,0- silicon max 6,0- copper max 0,5- manganese max 1,8- magnesium max 0,8- ferrum max 0,5- zinc max |
Loose, pressed |
0,5 |
|
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact When the content of Cutting fluid >10 %, calculation of clog to do according to the formula Cutting fluid (fact) - Cutting fluid (10%)=% additional clog Example: 19,5% - 10%=9,5% additional clog |
By the presence and moisture of oil or emulsion |
||||
Б 6 (Shavings of aluminum) |
Shavings of aluminum alloys of the system aluminum-silicon-copper |
13,0- silicon max 6,0- copper max 0,5- manganese max 1,4- magnesium max 1,0- ferrum max 1,0- zinc max |
Loose, pressed |
0,5 |
|
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact When the content of Cutting fluid >10 %, calculation of clog to do according to the formula Cutting fluid (fact) - Cutting fluid (10%)=% additional clog Example: 19,5% - 10%=9,5% additional clog |
By the presence and moisture of oil or emulsion |
||||
Б10 (Shavings of aluminum) |
The deformed aluminum alloys with high zinc content |
0,7- silicon max 2,6- copper max 0,5- manganese max 6,8- magnesium max 0,7- ferrum max 9,0- zinc max |
Loose, pressed |
0,5+ (% Zn -1)+ (% Mg -2) |
|
Dry and clean the scrap, not oxidized |
|||||
Not clogged by other metals, alloys |
|||||
Failure to comply with these requirements receives an additional clog in fact When the content of Cutting fluid >10 %, calculation of clog to do according to the formula Cutting fluid (fact) - Cutting fluid (10%)=% additional clog Example: 19,5% - 10%=9,5% additional clog |
By the presence and moisture of oil or emulsion |
||||
Г12 imported |
Slags |
By chemical composition |
Metallurgical output is not less than 30% |
Not clogged by other metals, alloys |
According to the obtained metallurgical balance output from smelting, the chemical composition |
The allowable overall dimensions of the scrap aluminum 1000x1000 mm. At discrepancy dimensions to large-sized scrap exhibited an additional discount on the cut.
Download the list of documents for the contract.